Android System for V3 Smart Controller (6.4" & 7.9")
Added support for the new camera model: XL706 (6K Pro)
Note: The XL706 (6K Pro) does not support panoramic features.
Added system certification information
Optimized aircraft wind resistance performance to comply with Chinese regulatory standards.
Removed low battery warning in Attitude Mode.
Fixed altitude deviation during rapid vertical movement in GNSS mode.
Fixed false no-fly zone alerts under weak GNSS signal conditions.
Fixed an issue where the “Gimbal Initialization Failed” error occurred after calibrating the gimbal and then power cycling the aircraft.
Fixed issues with auto-uploading flight records to third-party platforms.
Fixed other known issues.
Notes
Android system V1.3.9.23 is only for EVO II V3
To fully utilize all the new features in V3.1.134 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.4.4 before flying.
Resource
EVO II V3 Manual Update Instructions: https://drive.google.com/file/d/1ANqz_wZqCmUN-QgWWMgJcFGAN_RsirTf/view?usp=sharing
Livedeck II Firmware: https://www.autelrobotics.com/doc/evoii-livedeck-ii-firmware
V3 Smart Controller Android System: https://www.autelrobotics.com/download/559.html
Autel Explorer App: https://www.autelrobotics.com/download/27
EVO II V3 Firmware: https://www.autelrobotics.com/download/543.html
EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/544.html
Update Method & Steps:
OTA Update:
Please ensure that the internet connection remains stable throughout the process.
Open the Explorer app and tap the settings icon in the camera view.
Go to General, then select Software Update, and tap on Android System.
Click on Start Updating.
The update process should take approximately 15 minutes to complete.
Once the update is finished, the controller will automatically power cycle.
Manual Update:
Begin by downloading the Android System zip file.
Transfer the downloaded file onto an SD card.
Insert the SD card into the Smart Controller. If needed, you can utilize a USB converter for this step.
Navigate to Settings > General > Software Update > Android System.
Select the option for USB flash disk update.
Choose the file from the SD card and initiate the manual update process.
Added Remote ID function in China
Added Pairing method: Double click battery power button to enter pairing mode
Optimized video transmission feed performance
Optimized No-fly zone function
Optimized Remote ID function
Optimized HDMI function
Fixed GPS update error issue
Fixed other known issues.
Notes
Android system V1.3.9.15 is only for EVO II V3
To fully utilize all the new features in V3.1.107 Autel Explorer app, it's important to update your EVO II V3 firmware to V1.1.78 before flying.
Resource
Livedeck II Firmware:https://www.autelrobotics.com/doc/livedeck_ii_firmware
V3 Smart Controller Android System:https://www.autelrobotics.com/download/569.html
Autel Explorer App: https://www.autelrobotics.com/download/49
EVO II V3 Firmware: https://www.autelrobotics.com/download/545.html
EVO II V3 Firmware Version Table: https://www.autelrobotics.com/download/546.html
Update Method & Steps:
OTA Update:
Please ensure that the internet connection remains stable throughout the process.
Open the Explorer app and tap the settings icon in the camera view.
Go to General, then select Software Update, and tap on Android System.
Click on Start Updating.
The update process should take approximately 15 minutes to complete.
Once the update is finished, the controller will automatically power cycle.
Manual Update:
Begin by downloading the Android System zip file.
Transfer the downloaded file onto an SD card.
Insert the SD card into the Smart Controller. If needed, you can utilize a USB converter for this step.
Navigate to Settings > General > Software Update > Android System.
Select the option for USB flash disk update.
Choose the file from the SD card and initiate the manual update process.
